Helping a friend turn a van into a home—especially in a place as scenic as Cornwall—is a big undertaking, but getting the floor right is the best way to ensure the build lasts.
The first step to turning Catherine’s van into a home is getting a solid, insulated floor. Here is how we will tackle it:
Prepping and Battening
We will start by cleaning the metal ribs of the floor. We will glue 12mm thick wooden strips (battens) directly onto the high ridges of the metal floor using a high-strength adhesive like Sikaflex. This creates a level frame and gives us something to screw the plywood into later.
Insulation (The Warmth Factor)
Between the wooden battens, we will lay sheets of 25mm or 50mm rigid foam insulation. It’s vital to cut these for a snug fit.
- Tip: We won’t use a plastic vapour barrier to avoid trapping moisture against the metal. Instead, we will seal all the seams with foil tape to create a seamless, moisture-resistant layer.
Laying the Subfloor
Once the insulation is flat and flush with our wooden battens, we will lay 12mm WBP Plywood over the top. We will screw the ply into the wooden battens (not the metal van floor!) to secure it.
The Result
A flat, insulated, and rock-solid base ready for the final flooring and the rest of the build!
To answer any of your technical questions first:
The Vapour Barrier Debate
In the van-building community, this is a hot topic. However, the general consensus for a floor is no, don’t use a plastic sheet. The Risk: Metal “sweats” due to temperature changes. If you trap moisture between a plastic sheet and the metal floor, it has nowhere to go, which can lead to rust.
The Better Way: Use a “closed-cell” insulation (like Celotex or Kingspan). These boards don’t absorb water, effectively acting as their own barrier. Seal the gaps between the boards and the wooden strips with aluminium foil tape to keep moisture from reaching the metal.
Plywood Depth
For the subfloor, you want a balance between strength and weight.
12mm Plywood is the “Goldilocks” thickness. It’s sturdy enough to screw furniture into and won’t flex underfoot, but it isn’t unnecessarily heavy.
Note: Make sure you use Marine Grade or WBP (Weather and Boil Proof) plywood, as it handles the damp much better than standard interior ply.

To get that floor professionally installed, Catherine and I are going to need a mix of measuring, cutting, and fixing tools. Here is our essential kit list:
1. Measuring & Marking
- Tape Measure: Essential for getting those battens and insulation boards to the right length.
- Spirit Level: To check the floor is reasonably flat before we screw the plywood down.
- Carpenter’s Pencil or Sharpie: For marking lines on the wood and the shiny insulation.
2. Cutting Tools
- Jigsaw: This is the MVP. We’ll need it to cut the curves of the plywood to fit the wheel arches and the van’s walls. Use a “clean cut” wood blade.
- Handsaw: Useful for quick, straight cuts on our wooden battens.
- Stanley Knife (Utility Knife): The best tool for cutting through rigid foam insulation boards.
3. Fixing & Assembly
- Caulking Gun: We’ll need this to apply the Sikaflex or similar high-strength adhesive to the floor ridges.
- Combi Drill / Driver: For pre-drilling holes in our plywood and driving in the screws.
- Countersink Bit: This allows the screw heads to sit flush with the plywood so they don’t poke through Catherine’s final flooring (like lino or laminate).
- Wood Screws: 25mm or 30mm screws should do the trick for securing 12mm ply to our battens.
4. Finishing & Safety
- Foil Tape: To seal all the gaps between the insulation and the wood.
- Sandpaper: To smooth off any rough edges on the plywood after we’ve cut it to shape.
- PPE: Safety glasses for when we’re using the jigsaw and a dust mask for the plywood “sawdust.”
Pro Tip: If the van has any surface rust on the floor, grab a wire brush and some rust-converter paint to treat those spots before you glue anything down. It’s much easier to fix now than in three years’ time!




Leave a Reply